Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 102

Страница: 102 / 148

Case Temperature Reference Metrology

102

Thermal and Mechanical Design Guidelines

Figure

7-27. Solder Station Setup

27.

Remove the land side protective cover and place the device to be soldered in the

solder station. Make sure the thermocouple wire for the device being soldered is

exiting the heater toward you.

Note:

Do not touch the copper heater block at any time as this is very hot.

28.

Move a magnified lens light close to the device in the solder status to get a better

view when the solder begins to melt.

29.

Lower the Heater block onto the IHS. Monitor the device IHS temperature during

this step to ensure the maximum IHS temperature is not exceeded.

Note:

The target IHS temperature during reflow is 150 °C ±3 °C. At no time should the IHS
temperature exceed 155 °C during the solder process as damage to the device may
occur.

30.

You may need to move the solder back toward the groove as the IHS begins to

heat. Use a fine tip tweezers to push the solder into the end of the groove until a
solder ball is built up (Figure

7-28 and Figure

7-29).

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды