Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 53

Страница: 53 / 148

Balanced Technology Extended (BTX) Thermal/Mechanical Design Information

Thermal and Mechanical Design Guidelines

mounting hole position for TMA attach, the required preload is approximately 10-15N
greater than the values stipulated in Figure

5-6; however, Intel has not conducted any

validation testing with this TMA mounting scheme.

Figure

5-7. Thermal Module Attach Pointes and Duct-to-SRM Interface Features

SRM

Front attach point
use 6x32 screw
See detail A

Detail A

See detail B

Detail B

Rear attach point
use 6x32 screw

Chassis PEM nut

Duct front interface

feature see note 2

SRM

Front attach point
use 6x32 screw
See detail A

Detail A

See detail B

Detail B

Rear attach point
use 6x32 screw

Chassis PEM nut

Duct front interface

feature see note 2

NOTES:

For clarity the motherboard is not shown in this figure. In an actual assembly, the

captive 6x32 screws in the thermal module pass through the rear holes in the
motherboard designated in the socket keep-in Figure

7-50 through Figure

7-54 in

Appendix H and screw into the SRM and chassis PEM features.

This front duct ramp feature has both outer and inner lead-in that allows the feature to

slide easily into the SRM slot and around the chassis PEM nut. Note that the front PEM

nut is part of the chassis not the SRM.

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды