Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 105

Страница: 105 / 148

Case Temperature Reference Metrology

Thermal and Mechanical Design Guidelines

105

D.5.4

Cleaning and Completion of Thermocouple

Installation

33.

Remove the device from the solder station and continue to monitor IHS

Temperature with a handheld meter. Place the device under the microscope and

remove the three pieces of Kapton* tape with Tweezers, keeping the longest for

re-use.

34.

Straighten the wire and work the wire in to the groove. Bend the thermocouple

over the IHS. Replace the long piece of Kapton* tape at the edge of the IHS.

Note:

The wire needs to be straight so it doesn’t sit above the IHS surface at anytime (see
Figure

7-31).

Figure

7-31. Thermocouple placed into groove

35.

Using a blade carefully shave the excess solder above the IHS surface. Only shave
in one direction until solder is flush with the groove surface (see Figure

7-32).

Figure

7-32. Removing Excess Solder

Note:

Take usual precautions when using open blades

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды