Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 91

Страница: 91 / 148

Case Temperature Reference Metrology

Thermal and Mechanical Design Guidelines

D.3

Thermal Calibration and Controls

It is recommended that full and routine calibration of temperature measurement

equipment be performed before attempting to perform temperature case

measurement. Intel recommends checking the meter probe set against known

standards. This should be done at 0 ºC (using ice bath or other stable temperature

source) and at an elevated temperature, around 80 ºC (using an appropriate

temperature source).

Wire gauge and length also should be considered as some less expensive

measurement systems are heavily impacted by impedance. There are numerous

resources available throughout the industry to assist with implementation of proper

controls for thermal measurements.

NOTES:

It is recommended to follow company standard procedures and wear safety

items like glasses for cutting the IHS and gloves for chemical handling.

Please ask your Intel field sales representative if you need assistance to

groove and/or install a thermocouple according to the reference process.

D.4

IHS Groove

Cut a groove in the package IHS; see the drawings given in Figure

7-12 and

Figure

7-13. The groove orientation in Figure

7-12 is toward the IHS notch to allow

the thermocouple wire to be routed under the socket lid. This will protect the

thermocouple from getting damaged or pinched when removing and installing the
heatsink (see Figure

7-37).

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды