Intel 80C186EA Скачать руководство пользователя страница 272 | Manualshive

Страница: 272 / 417

background image

10-5

DIRECT MEMORY ACCESS UNIT

10.1.4.1 Source Synchronization

A typical source-synchronized transfer is shown in Figure 10-3. Most DMA-driven peripherals
deassert their DRQ line only after the DMA transfer has begun. The DRQ signal must be deas-
serted at least four clocks before the end of the DMA transfer (at the T1 state of the deposit phase)
to prevent another DMA cycle from occurring. A source-synchronized transfer provides the
source device at least three clock cycles from the time it is accessed (acknowledged) to deassert
its request line if further transfers are not required.

Figure 10-3. Source-Synchronized Transfers

10.1.4.2 Destination Synchronization

A destination-synchronized transfer differs from a source-synchronized transfer by the addition
of two idle states at the end of the deposit cycle (Figure 10-4). The two idle states extend the DMA
cycle to allow the destination device to deassert its DRQ pin four clocks before the end of the
cycle. If the two idle states were not inserted, the destination device would not be able to deassert
its request in time to prevent another DMA cycle from occurring.

The insertion of two idle states at the end of a destination synchronization transfer has an impor-
tant side effect. A destination-synchronized DMA channel gives up the bus during the idle
states, allowing any other bus master to gain ownership. This includes the CPU, the Refresh
Control Unit, an external bus master or another DMA channel.

T1

T2

T3

T4

CLKOUT

DRQ (Case 1)

T1

T2

T3

T4

DRQ (Case 2)

Fetch Cycle

Deposit Cycle

NOTES:
1. Current source synchronized transfer will not be immediately
followed by another DMA transfer.
2. Current source synchronized transfer will be immediately
followed by another DMA transfer.

2

1

A1188-0A

«
...
270
271
272
273
274
...
»

Содержание 80C186EA


































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80C186EA

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: Omega Engineering Страницы: 34

Бренд: IOtech Страницы: 16

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

Surround Dongle

Бренд: Sennheiser Страницы: 18

Бренд: AXAGO Страницы: 2

Бренд: Freescale Semiconductor Страницы: 8

NVRx-7300 series

Бренд: Swann Страницы: 9

Бренд: ANEP Страницы: 48

Бренд: IEI Technology Страницы: 2

Бренд: Xantech Страницы: 5

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

KÜHLER H2O 920

Бренд: Antec Страницы: 6

IA611 Xplained Pro

Бренд: Knowles Страницы: 14

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренд: Transition Networks Страницы: 1

Бренд: Extron electronics Страницы: 139

Pentium Pro Family

Бренд: Intel Страницы: 328

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды