IBM P260 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 524

background image

3.

Press the power-control button to turn off the compute node. See “Turning off the compute node” on
page 13.

4.

Wait at least 30 seconds for the hard disk drive to stop spinning.

5.

Open the release handles, as shown in Figure 8 on page 37. The IBM Flex System p260 Compute
Node has one release handle. The IBM Flex System p460 Compute Nodehas two release handles. The
compute node can be moved out of the bay approximately 0.6 cm (0.25 inch).

6.

Pull the compute node out of the bay.

7.

Carefully lay the compute node on a flat, static-protective surface, with the cover side up.

8.

Place either a compute node filler or another compute node in the bay.

Reseating the compute node in a chassis

Reseat the compute node.

About this task

To reseat the compute node, complete the following steps:

Procedure

1.

Perform a virtual reseat of the compute node.

To perform a virtual reseat by using the IBM Chassis Management Module (CMM), go to
http://pic.dhe.ibm.com/infocenter/flexsys/information/topic/com.ibm.acc.8731.doc/
unmanaging_chassis.html.
To perform a virtual reseat by using the IBM Flex System Manager (FSM), go to http://
pic.dhe.ibm.com/infocenter/flexsys/information/topic/com.ibm.acc.8731.doc/
unmanaging_chassis.html.

2.

Is the problem resolved?

Yes:

This ends the procedure.

No:

Continue with the next step.

3.

Remove and replace the compute node into the IBM Flex System Enterprise Chassis.

a.

Remove the compute node from the IBM Flex System Enterprise Chassis. See “Removing the
compute node from an IBM Flex System Enterprise Chassis” on page 37.

b.

Install the compute node into the IBM Flex System Enterprise Chassis. See “Installing the compute
node in an IBM Flex System Enterprise Chassis” on page 93.

38

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

«
...
48
49
50
51
52
...
»

Содержание P260













































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P260

Baby Control BC-439

Бренд: Hama Страницы: 20

Бренд: C.ITOH Страницы: 196

Бренд: Alecto Страницы: 24

UltraView AP-10AV Series

Бренд: I-Tech Страницы: 28

Бренд: Levita Страницы: 28

Бренд: Welch Allyn Страницы: 39

Бренд: Emgeton Страницы: 84

Бренд: Topcom Страницы: 96

Бренд: Navman Страницы: 28

VA2016W - 20" LCD Monitor

Бренд: ViewSonic Страницы: 23

Бренд: Microtek Страницы: 17

Бренд: ViewSonic Страницы: 132

Бренд: ViewSonic Страницы: 2

Бренд: Garmin Страницы: 10

Бренд: Velleman Страницы: 21

VOYIX 7772-K461

Бренд: NCR Страницы: 10

Бренд: Samsung Страницы: 34

Бренд: Samsung Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды