IBM P260 Скачать руководство пользователя страница 315

Страница: 315 / 524

101-714

Explanation:

The system hung while trying to configure an unknown resource.

Run the stand-alone diagnostics problem determination procedure.

If the problem remains, refer to Failing function codes to find the FFC that matches the last three digits of the
SRN.

Suspect the device adapter or device itself.

Response:

Failing Item:

FFC_714

101-715

Explanation:

The system hung while trying to configure an unknown resource.

Run the stand-alone diagnostics problem determination procedure.

If the problem remains, refer to Failing function codes to find the FFC that matches the last three digits of the
SRN.

Suspect the device adapter or device itself.

Response:

Failing Item:

FFC_715

101-716

Explanation:

The system hung while trying to configure an unknown resource.

Run the stand-alone diagnostics problem determination procedure.

If the problem remains, refer to Failing function codes to find the FFC that matches the last three digits of the
SRN.

Suspect the device adapter or device itself.

Response:

Failing Item:

FFC_716

101-717

Explanation:

The system hung while trying to configure an unknown resource.

Run the stand-alone diagnostics problem determination procedure.

If the problem remains, refer to Failing function codes to find the FFC that matches the last three digits of the
SRN.

Suspect the device adapter or device itself.

Response:

Failing Item:

FFC_717

101-714 • 101-717

Chapter 8. Troubleshooting

303

Содержание P260













































































































































































































































































































































































































































































































































Результаты поиска

Содержание P260

Отзывы:

Похожие инструкции для P260

Бренды по названию

Популярные бренды

IBM P260, Инструкция по установке и обслуживанию

Результаты поиска

Содержание P260

Отзывы:

Похожие инструкции для P260

Бренды по названию

Популярные бренды