IBM P260 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 524

background image

CAUTION:
Data processing environments can contain equipment transmitting on system links with laser modules
that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical
fiber cable or open receptacle. (C027)

CAUTION:
This product contains a Class 1M laser. Do not view directly with optical instruments. (C028)

CAUTION:
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following
information: laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam. (C030)

CAUTION:
The battery contains lithium. To avoid possible explosion, do not burn or charge the battery.

Do Not:

v

___ Throw or immerse into water

v

___ Heat to more than 100°C (212°F)

v

___ Repair or disassemble

Exchange only with the IBM-approved part. Recycle or discard the battery as instructed by local
regulations. In the United States, IBM has a process for the collection of this battery. For information,
call 1-800-426-4333. Have the IBM part number for the battery unit available when you call. (C003)

Power and cabling information for NEBS (Network Equipment-Building System)
GR-1089-CORE

The following comments apply to the servers that have been designated as conforming to NEBS
(Network Equipment-Building System) GR-1089-CORE:

The equipment is suitable for installation in the following:

v

Network telecommunications facilities

v

Locations where the NEC (National Electrical Code) applies

The intrabuilding ports of this equipment are suitable for connection to intrabuilding or unexposed
wiring or cabling only. The intrabuilding ports of this equipment must not be metallically connected to the
interfaces that connect to the OSP (outside plant) or its wiring. These interfaces are designed for use as
intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation
from the exposed OSP cabling. The addition of primary protectors is not sufficient protection to connect
these interfaces metallically to OSP wiring.

Note:

All Ethernet cables must be shielded and grounded at both ends.

The ac-powered system does not require the use of an external surge protection device (SPD).

The dc-powered system employs an isolated DC return (DC-I) design. The DC battery return terminal
shall not be connected to the chassis or frame ground.

x

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

«
...
10
11
12
13
14
...
»

Содержание P260













































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P260

Бренд: Ocean Matrix Страницы: 2

SyncMaster 1200NF

Бренд: Samsung Страницы: 30

SyncMaster 172W

Бренд: Samsung Страницы: 45

SyncMaster 2032GWPlus

Бренд: Samsung Страницы: 62

SyncMaster 2033SN

Бренд: Samsung Страницы: 91

SyncMaster 1100MB

Бренд: Samsung Страницы: 62

SyncMaster 171B, 171S, 181B, 171T, 171Q

Бренд: Samsung Страницы: 83

SyncMaster SM320MX-2

Бренд: Samsung Страницы: 109

T200HD - SyncMaster - 20" LCD Monitor

Бренд: Samsung Страницы: 27

SyncMaster TC180

Бренд: Samsung Страницы: 2

T220HD - SyncMaster - 22" LCD Monitor

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 241

SyncMaster XL2270

Бренд: Samsung Страницы: 43

SyncMaster S24A460B

Бренд: Samsung Страницы: 44

SyncMaster S22A300N

Бренд: Samsung Страницы: 48

SyncMaster S27A850D

Бренд: Samsung Страницы: 89

SyncMaster S22A650D

Бренд: Samsung Страницы: 94

SyncMaster S22A650S

Бренд: Samsung Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды