IBM P260 Скачать руководство пользователя страница 198 | Manualshive

Страница: 198 / 524

background image

B7006A22

Explanation:

PCI-E switch had a recoverable failure, however, all downstream I/O had to be failed during recovery.

Recovery for the PCI-E switch failure is being attempted. If the recovery is successful, no other SRC is logged.

Response:

Once the PCI-E switch is recovered, the downstream I/O adapters should recover. The partition or

application associated with the failed downstream I/O may have to be restarted.

B7006A23

Explanation:

PCI-E switch recovery failure. All downstream I/O is failed.

Response:

If there are any AIX or Linux errors logged against I/O adapters on this switch, do not replace any I/O

adapter hardware. This PCI-E switch failure is the root cause.

1.

Collect error logs and info logs.

2.

Collect the configuration data for the IOAs downstream of the PCI-E switch.

3.

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis assembly.

4.

Although the partition or application may have continued to run after the I/O adapter failures, it might need to
be restarted to recover.

B7006A24

Explanation:

PCI-E switch had an unrecoverable failure. All downstream I/O is failed.

Response:

1.

Collect error logs and info logs.

2.

Collect the configuration data for the IOAs downstream of the PCI-E switch.

3.

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis assembly.
Send the failed FRU and the data to IBM for fault analysis.

B7006A25

Explanation:

PCI-E switch has detected a firmware action that was not valid. All downstream I/O is failed.

Response:

1.

Collect error logs and info logs.

2.

Collect the configuration data for the IOAs downstream of the PCI-E switch.

3.

Update the firmware to the current level, as described in Updating the firmware.

4.

If the problem persists, replace the system-board and chassis assembly, as described in Replacing the
system-board and chassis assembly. Send the failed FRU and the data to IBM for fault analysis.

B7006A22 • B7006A25

186

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

«
...
196
197
198
199
200
...
»

Содержание P260













































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P260

Бренд: NCR Страницы: 54

DVX-2821 Series

Бренд: Daktronics Страницы: 20

Бренд: Samsung Страницы: 37

Cintiq Pro DTH-3220

Бренд: Wacom Страницы: 78

Бренд: ITI Страницы: 6

VPPE-3-1-1/8-x-E1 Series

Бренд: Festo Страницы: 2

Бренд: ViewSonic Страницы: 66

Бренд: HANNspree Страницы: 23

Бренд: ADEMCO Страницы: 20

Babyviewer 2500

Бренд: Levita Страницы: 18

UltraView iAP1000AV

Бренд: I-Tech Страницы: 1

Бренд: Partron Страницы: 25

Бренд: Hansol Страницы: 14

Бренд: Tommee Tippee Страницы: 10

Бренд: Viotek Страницы: 20

I9 WIDE CMV 955A-C

Бренд: Chimei Страницы: 36

Бренд: AOC Страницы: 30

Бренд: Garmin Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды