IBM P260 Скачать руководство пользователя страница 456

Страница: 456 / 524

SSSS-135

Explanation:

The device failed to configure.

Check the BladeCenter management-module event log. If an error was recorded by the system, see POST progress
codes (checkpoints).

Replace any parts reported by the diagnostic program.

Replace the system board and chassis assembly, as described in Replacing the system-board and chassis assembly.

Response:

Failing Item:

FFC_SSSS

FFC_252B

SOFTWARE

SSSS-136

Explanation:

The certify operation failed.

Check the BladeCenter management-module event log. If an error was recorded by the system, see POST progress
codes (checkpoints).

Replace any parts reported by the diagnostic program.

Replace the system board and chassis assembly, as described in Replacing the system-board and chassis assembly.

Response:

Failing Item:

FFC_SSSS

SSSS-137

Explanation:

Unit attention condition has occurred on the Send Diagnostic command.

Check the BladeCenter management-module event log. If an error was recorded by the system, see POST progress
codes (checkpoints).

Replace any parts reported by the diagnostic program.

Replace the system board and chassis assembly, as described in Replacing the system-board and chassis assembly.

Response:

Failing Item:

FFC_SSSS

FFC_252B

SSSS-135 • SSSS-137

444

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Содержание P260













































































































































































































































































































































































































































































































































Результаты поиска

Содержание P260

Отзывы:

Похожие инструкции для P260

Бренды по названию

Популярные бренды

IBM P260, Инструкция по установке и обслуживанию

Результаты поиска

Содержание P260

Отзывы:

Похожие инструкции для P260

Бренды по названию

Популярные бренды