IBM P260 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 524

background image

Turning off the compute node

When you turn off the compute node, it is still connected to power through the IBM Flex System
Enterprise Chassis. The compute node can respond to requests from the service processor, such as a
remote request to turn on the compute node. To remove all power from the compute node, you must
remove it from the IBM Flex System Enterprise Chassis.

Before you begin

Shut down the operating system before you turn off the compute node. See the operating-system
documentation for information about shutting down the operating system.

About this task

To turn off the compute node, use one of the following methods:

Procedure

v

Turn off the compute node by pressing the power-control button for at least 5 seconds.

Note:

The power-control LED can remain on solidly for up to 1 minute after you push the

power-control button. After you turn off the compute node, wait until the power-control LED is
flashing slowly before you press the power-control button to turn on the compute node again.
If the operating system stops functioning, press and hold the power-control button for more than 5
seconds to force the compute node to turn off.

v

Use the management module to turn off the compute node.
The power-control LED can remain on solidly for up to 1 minute after you initiate the power-off
process. After you turn off the compute node, wait until the power-control LED is flashing slowly
before you initiate the power-on process from the Chassis Management Module (CMM) to turn on the
compute node again.
Use the management-module Web interface to configure the management module to turn off the
compute node if the system is not operating correctly.
For additional information, see http://publib.boulder.ibm.com/infocenter/flexsys/information/topic/
com.ibm.acc.cmm.doc/cmm_product_page.html.

System-board layouts

Illustrations show the connectors and LEDs on the system board. The illustrations might differ slightly
from your hardware.

Chapter 2. Power, controls, indicators, and connectors

13

«
...
23
24
25
26
27
...
»

Содержание P260













































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P260

NEC MultiSync LCD1525V LCD1525V LCD1525V

Бренд: NEC Страницы: 2

MultiSync LCD2180UX

Бренд: NEC Страницы: 1

MultiSync LCD2010X

Бренд: NEC Страницы: 78

MultiSync LCD1970GX LCD1970GX LCD1970GX

Бренд: NEC Страницы: 2

MultiSync LCD195VXM+

Бренд: NEC Страницы: 17

MultiSync LCD195WXM

Бренд: NEC Страницы: 16

MultiSync FE791SB

Бренд: NEC Страницы: 50

PlasmaSync 42XC10

Бренд: NEC Страницы: 10

PlasmaSync 42XC10

Бренд: NEC Страницы: 3

MultiSync ME431

Бренд: NEC Страницы: 96

Бренд: Falcon Страницы: 16

AFID ADVANCED EASY

Бренд: Microlife Страницы: 33

Бренд: Digital Equipment Страницы: 76

PrecisionSensor Pro BP 2590 Instructions

Бренд: Braun Страницы: 66

MultiSync LCD1990FX

Бренд: NEC Страницы: 2

Бренд: 2E Страницы: 31

Reichert ClearChart 4P

Бренд: Ametek Страницы: 52

Бренд: Farenheit Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды