64
Hot-swap Models
Nonhot-swap Models
Part
Number
Description
RPM Height
Bays
Supported
2
Maximum
Quantity
Bays
Supported
Maximum
Quantity
Nonhot-swap Ultra160 SCSI HDDs
1
06P5750
18.2GB 10Krpm Ultra160 SCSI SL HDD
10000
SL
4
1
4 ... 7
4
06P5751
36.4GB 10Krpm Ultra160 SCSI SL HDD
10000
SL
4
1
4 ... 7
4
06P5752
73.4GB 10Krpm Ultra160 SCSI SL HDD
10000
SL
4
1
4 ... 7
4
06P5765
18.2GB 15Krpm Ultra160 SCSI SL HDD
15000
SL
4
1
4 ... 7
4
06P5766
36.4GB 15Krpm Ultra160 SCSI SL HDD
15000
SL
4
1
4 ... 7
4
Hot-swap Ultra160 SCSI HDDs
2
06P5754
18.2GB 10Krpm Ultra160 SCSI Hot-Swap SL HDD
10000
SL
5 ... 7
3
-
-
06P5755
36.4GB 10Krpm Ultra160 SCSI Hot-Swap SL HDD 10000
SL
5 ... 7
3
-
-
06P5756
73.4GB 10Krpm Ultra160 SCSI Hot-Swap SL HDD
10000
SL
5 ... 7
3
-
-
06P5767
18.2GB 15Krpm Ultra160 SCSI Hot-Swap SL HDD
15000
SL
5 ... 7
3
-
-
06P5768
36.4GB 15Krpm Ultra160 SCSI Hot-Swap SL HDD 15000
SL
5 ... 7
3
-
-
Optical Devices
Bays Supported
22P6950
16x Max RAM-Read DVD-ROM Drive
3, 4
1, 2
22P6976
40x-12x-40x Max Black CD-RW Drive
3
1, 2
External Storage Expansion Units
5
Form Factor
35311RU
EXP300 Storage Expansion Unit
6
Rack (3U)
09N7296
EXP300 Rack-to-Tower Conversion Kit
-
1. Nonhot-swap HDDs are supported in bays 4 ... 7 of nonhot-swap models and in bay four of hot-swap models. Nonhot-swap HDDs are not supported on the same SCSI bus as
the hot-swap backplane in hot-swap models.
2. Hot-swap HDDs are supported in bays 5 ... 7 of hot-swap models. Bay four supports nonhot-swap HDDs only. Nonhot-swap HDDs are not supported on the same SCSI bus as
the hot-swap backplane in hot-swap models.
3. Either replace the standard CD-ROM or install in the available media bay. An IDE cable with three connectors is included with the optional optical drive (same cable is standard
in the system). If installing as an additional device, connect the cable to each optical device and the IDE connector on the system board. Configure the optional device as a master
using the preset configuration if replacing the standard device or as a slave if installed as a redundant device.
4. Audio not supported for DVD-ROM drives. The drive provides data input/output only.
5. Not supported by the onboard SCSI controller. Select an optional SCSI controller then refer to Appendix D: Cables - Storage Units - Controllers to confirm the controller supports
the desired External Storage Expansion Unit and to select a supported cable. For HDD or other expansion unit options, see the specific expansion unit section.
6. EXP300 includes a single 2M Ultra2 SCSI cable and dual hot-swap 500W redundant power supplies, each with its own power cord. To convert an EXP300 to a tower form factor,
EXP300 Rack-to-Tower Conversion Kit (P/N 09N7296) is required.
Bay
Form
Factor
Height
Front
Access
Usage
1
133mm
(5.25in)
HH
yes
IDE CD-
ROM
2
133mm
(5.25in)
HH
yes
open
1
3
89mm
(3.5in)
SL
yes
Floppy
4
89mm
(3.5in)
SL
yes
open
5 ... 7
89mm
(3.5in)
SL
2
yes
open
Note: HDDs are installed in the order of bays seven through four, i.e.,
7, 6, 5, 4. The boot disk must be installed in bay seven (SCSI ID 0).
1. Supports removable media devices only. Hard disk drives are not
supported.
2. Bays five, six and seven are configured as hot-swap bays on xAX
models. These bays are not front-accessible in nonhot-swap
models.
Bay 4
CD-ROM
Bay 2
Diskette
Bay 5
Bay 6
Bay 7
Содержание 6219 - IntelliStation M - Pro
