Honda NC700 2012, Руководство по обслуживанию

Страница: 547 / 773

16-4
dummyhead dummyhead
ENGINE REMOVAL/INSTALLATION
SERVICE INFORMATION
GENERAL
• A hoist or equivalent is required to support the motorcycle when removing and installing the engine.
• When removing/installing the engine, tape the frame around the engine beforehand for frame protection.
• When installing the engine, be sure to tighten the engine mounting fasteners to the specified torque in the specified sequence. If
you mistake the torque or sequence, loosen all mounting fasteners, then tighten them again to the specified torque in the correct
sequence.
• The following components can be serviced with the engine installed in the frame.
– Starter motor (page 6-8)
– Throttle body (page 7-15)
– Water pump (page 8-12)
– Oil pump (NC700X/XA/S/SA) (page 9-6)
– Oil pump (NC700XD/SD) (page 9-8)
– Rocker arm (page 10-8)
– Clutch (NC700X/XA/S/SA) (page 11-7)
– Gearshift linkage (NC700X/XA/S/SA) (page 11-16)
– Primary drive gear/CKP sensor rotor (NC700X/XA/S/SA) (page 11-15)
– Dual clutch (NC700XD/SD) (page 12-105)
– Gearshift linkage (NC700XD/SD) (page 12-112)
– Primary drive gear/CKP sensor rotor (NC700XD/SD) (page 12-108)
– CKP sensor (page 5-11)
– Flywheel (page 13-7)
– Stator (page 13-13)
• The following components require engine removal for service.
– Camshaft (page 10-13)
– Cylinder head/valves (page 10-16)
– Transmission (NC700X/XA/S/SA) (page 14-8)
– Transmission (NC700XD/SD) (page 14-17)
– Balancer (page 14-26)
– Crankshaft (page 15-5)
– Piston/cylinder (page 15-14)
SPECIFICATIONS
TORQUE VALUES
ITEM SPECIFICATIONS
Engine dry
weight NC700X/XA/S/SA 60.5 kg (133.4 lbs)
NC700XD/SD 67.3 kg (148.4 lbs)
Engine oil
capacity NC700X/XA/S/SA After draining 3.1 liters (3.3 US qt, 2.7 Imp qt)
After draining/filter
change
3.4 liters (3.6 US qt, 3.0 Imp qt)
After disassembly 3.7 liters (3.9 US qt, 3.3 Imp qt)
NC700XD/SD After draining 3.2 liters (3.4 US qt, 2.8 Imp qt)
After draining/filter
change
3.4 liters (3.6 US qt, 3.0 Imp qt)
After disassembly 4.1 liters (4.3 US qt, 3.6 Imp qt)
Coolant
capacity Radiator and engine 1.69 liters (1.79 US qt, 1.49 Imp qt)
At draining 1.41 liters (1.49 US qt, 1.24 Imp qt)
Reserve tank 0.13 liter (0.14 US qt, 0.11 Imp qt)
ITEM Q'TY
THREAD TORQUE
REMARKS
DIA. (mm) N·m (kgf·m, lbf·ft)
Rear lower engine hunger nut 1 12 59 (6.0, 44)
Front lower engine hunger bolt 2 12 54 (5.5, 40)
Upper engine hunger bolt 2 12 54 (5.5, 40)
Rear upper engine hunger nut 1 12 54 (5.5, 40)
Step holder mounting socket bolt 4 8 32 (3.3, 24)
Drive sprocket bolt 1 10 54 (5.5, 40)
Starter motor terminal nut 1 6 10 (1.0, 7)
Water hose band screw 2 – – See page 16-18
See page 16-19
See page 16-24
See page 16-25