Hill-Rom 305 Manual Bed страница 17 Скачать руководство пользователя

Страница: 17 / 176

Safety Tips

Chapter 1: Introduction

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Page 1 - 9

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

WARNING:

Do not work under an unsupported load. Install applicable temporary
supports. Failure to do so could cause injury or equipment damage.

WARNING:

Put caster blocks behind the casters at the opposite end of the bed.
Failure to do so could cause injury.

WARNING:

Only facility-approved persons should service the bed. Service by not
approved persons could cause injury or equipment damage.

WARNING:

Obey the product manufacturer’s instructions. Failure to do so could
cause injury or equipment damage.

WARNING:

Attach the foot section to the head section. Failure to do so could cause
injury.

WARNING:

Powered bed mechanisms can cause injury. Operate the bed only
when persons are clear of the mechanisms. Failure to do so could
cause injury or death.

WARNING:

Remove the patient from the bed before you do this procedure. Failure
to do so could cause injury or equipment malfunction.

WARNING:

Wear eye protection. Failure to do so may cause eye injury.

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды

Hill-Rom 305 Manual Bed, Руководство по обслуживанию

Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды