Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 176

Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 18

Safety Tips
Chapter 1: Introduction

Page 1 - 10

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

WARNING:

If you use or handle the power cord improperly you may cause damage
to the power cord. If damage has occurred to the power cord or any of
its components, immediately remove the unit from service, and contact
the applicable maintenance person. Failure to do so could cause
electrical shock or other injury or equipment damage.

WARNING:

Fluid spills onto the bed electronics can cause a hazard. If such a spill
occurs, unplug the bed, and remove it from service. Failure to do so
could cause injury or equipment damage.

WARNING:

Follow applicable infection control policies and procedures. Failure to
do so could cause the spread of infection.

WARNING:

Install the IV pole correctly. Failure to do so could cause injury or
equipment damage.

SHOCK HAZARD:

Disconnect the bed from its power source. Failure to do so could cause
injury or equipment damage.

SHOCK HAZARD:

Do not expose the unit to excessive moisture. Injury or equipment
damage could occur.

SHOCK HAZARD:

The potential for electrical shock exists with electrical equipment.
Failure to follow facility protocols may cause death or injury.

CAUTION:

Make sure that a flat side of the hex rod faces upward when it is
installed. Failure to do so may cause the central brake and steer to
operate incorrectly.

«
...
16
17
18
19
20
...
»

Содержание 305 Manual Bed

















































































































































































Отзывы:

Нет отзывов