Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 156

Страница: 156 / 176

Component Handling
Chapter 6: General Procedures

Page 6 - 2

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

Steam Cleaning

Do not steam clean the bed. Excessive moisture can damage mechanisms and
components in this unit.

Hard to Clean Spots

To remove difficult spots or stains, use standard household cleaners and a soft
bristle brush. To loosen heavy, dried-on soil or excreta, it may be necessary to
first saturate the spot.

Disinfecting

Dilute disinfectants and germicides as specified on the manufacturer’s label.

Component Handling

CAUTION:

Make sure that your hands are clean, and

only

handle the PC boards

by their edges to prevent component damage.

CAUTION:

Wear an antistatic strap when you handle electronic components.
Failure to do so could cause component damage

CAUTION:

Put the removed PC boards in antistatic protective bags to ship or store
the PC boards. Equipment damage can occur.

PC Board

Be careful with the PC board when you service it, damage or malfunctions may
occur:

• PC board damage

• Shortened PC board life

• Unit malfunctions

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Hill-Rom 305 Manual Bed, Руководство по обслуживанию, Страница: 156 / 176

Результаты поиска

Содержание 305 Manual Bed

Отзывы: