Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 119

Страница: 119 / 176

4.30 Sleep Surface Panels

Chapter 4: Removal, Replacement, and Adjustment Procedures

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Page 4 - 67

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

b. Remove the two retaining rings (C) and two pins (D) that attach the

foot panel (F) to the bed frame (E) (see figure 4-31 on page 4-66).

c. Remove the foot panel (F) from the bed frame (E).

5. If you replace the mattress stop (K), do as follows:

a. Remove the two screws (L).

b. Remove the mattress stop (K).

6. If you replace a head panel (H), do as follows:

a. Remove the two headrails (I) from the bed frame (E) (refer to

procedure 4.16 on page 4-37).

b. Remove the CPR handle assembly (J) from the bed frame (E) (refer to

procedure 4.15 on page 4-35).

c. Remove the two retaining rings (C) and two pins (D) that attach the

head panel (H) to the bed frame (E) (see figure 4-31 on page 4-66).

d. Remove the head panel (H) from the bed frame (E).

Replacement

1. Do the removal procedure in the reverse order.

2. Do the “Function Checks” on page 2-2.

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Hill-Rom 305 Manual Bed, Руководство по обслуживанию, Страница: 119 / 176

Результаты поиска

Содержание 305 Manual Bed

Отзывы: