manualshive.com logo in svg

Hill-Rom 305 Manual Bed, Руководство по обслуживанию, Страница: 89 / 176

Поделиться
Скачать
Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 89

4.16  Siderails

Chapter 4: Removal, Replacement, and Adjustment Procedures

4

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Page 4 - 37 

 

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

4.16 Siderails

Tools required:

5 mm hex wrench

 

Wire cutters

Removal

Prepare the Bed

1. Disconnect the battery cable from the control board (refer to procedure 4.7 

on page 4-16).

2. Raise the bed to the highest position.

3. If you replace a headrail (A), raise the head section (B) to the highest 

position (see figure 4-16 on page 4-38).

4. If you replace a footrail (C), do as follows:

a. Raise the head section (B) and the knee section (D) to their highest 

positions.

b. Lift the foot section (E) of the sleep surface, and fold it back toward the 

head section (B).

WARNING:

Attach the foot section to the head section. Failure to do so could cause 
injury.

c. Use straps to attach the foot section (E) to the head section (B).

SHOCK HAZARD:

Disconnect the bed from its power source. Failure to do so could cause 
injury or equipment damage.

5. Disconnect the bed from its power source.

Remove the Siderails

1. If the siderail is a footrail (C) or if the bed is a manual bed, do as follows:

a. Remove the two screws (F) and the slide bracket (G) that attaches the 

siderail to the bed frame (H). 

Содержание 305 Manual Bed

















































































































































































Отзывы:

Нет отзывов