Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 70

Страница: 70 / 176

4.8 Head Motor
Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 18

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

4.8

Head Motor

Tools required:

Needle nose pliers

Wire cutters

Removal

1. Disconnect the battery cable from the control board (refer to procedure 4.7

on page 4-16).

2. Raise the bed to the highest position.

SHOCK HAZARD:

Disconnect the bed from its power source. Failure to do so could cause
injury or equipment damage.

3. Disconnect the bed from its power source.

4. Use the CPR handle (A), to lower the head section (B) to the lowest

position (see figure 4-8 on page 4-19).

5. Make a note to show how the cable routes from the head motor (C) to the

control box assembly (D).

CAUTION:

Use caution when you cut the wire ties. Failure to do so could cause
cable damage.

6. Carefully cut all of the wires ties that attach the head motor cable (E) to the

bed frame (F).

7. Remove the CPR cable (G) from the head motor (C) (refer to procedure 4.9

on page 4-20).

8. Disconnect the head motor cable (E) from the control box assembly (D).

9. Remove the retaining ring (H) and pin (I) that attach the head motor (C) to

the bed frame (F).

10. Remove the retaining ring (J) and pin (K) that attach the head motor (C) to

the mounting bracket (L).

11. Remove the head motor (C).

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Hill-Rom 305 Manual Bed, Руководство по обслуживанию, Страница: 70 / 176

Результаты поиска

Содержание 305 Manual Bed

Отзывы: