Hill-Rom 305 Manual Bed страница 109 Скачать руководство пользователя

Страница: 109 / 176

4.25 Central Brake and Steer—Caster Assemblies

Chapter 4: Removal, Replacement, and Adjustment Procedures

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Page 4 - 57

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

NOTE:

As the hex rod is pushed through the caster, the caster will fall off the bed
frame.

9. Do step 4 through step 8 for the opposite caster assembly.

10. Go to “Replace the Head End” on page 4-58.

Replacement

Replace the Foot End

1. Make sure the caster is in the neutral or center position.

2. Install the brake and steer caster (C) in the bed frame (D) with the red dot

(Q) on the left-hand side and the green dot (R) on the right-hand side (see
figure 4-25 on page 4-55).

NOTE:

When left-hand and right-hand sides of the bed are identified, they are from the
patient’s point of view.

CAUTION:

Make sure that a flat side of the hex rod faces upward when it is
installed. Failure to do so may cause the central brake and steer to not
operate correctly.

3. Push the hex rod (G) through the opening in the bed frame (D) and through

the brake and steer caster (C).

4. Push the hex rod (G) through the rocker arm (I).

5. Push the hex rod (G) into the bracket (H) on the bed frame (D).

6. Install the bolt (A) and washer (B) to attach the brake and steer caster (C)

to the bed frame (D).

7. Install the bolt (E) and washer (F) to attach the hex rod (G) to the bracket

(H).

8. Install the bolt (K) and nut (L) to attach the linkage (M) to the rocker arm

(J).

9. Tighten the setscrew (I) on the rocker arm (J).

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды

Hill-Rom 305 Manual Bed, Руководство по обслуживанию

Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды