Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 10

Страница: 10 / 176

Document Symbols
Chapter 1: Introduction

Page 1 - 2

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

Document Symbols

This manual contains different typefaces and symbols designed to improve
readability and increase your knowledge of its content:

• Standard text—used for regular data.

•

Boldface text

—emphasizes a word or phrase.

•

NOTE:

—sets apart special data or important instruction clarification.

• The symbol below shows a WARNING or CAUTION:

Figure 1-1. Warning and Caution

– A WARNING identifies situations or actions that could affect

patient or user safety. Disobeying a warning could cause patient
or user injury.

– A CAUTION points out special procedures or precautions that a

person must obey to avoid equipment damage.

• The symbol below identifies a CAUGHT HAZARD WARNING:

Figure 1-2. Caught Hazard Warning

• The symbol below identifies a CHEMICAL HAZARD WARNING:

Figure 1-3. Chemical Hazard Warning

• The symbol below identifies an ELECTRICAL SHOCK HAZARD

WARNING:

Figure 1-4. Electrical Shock Hazard Warning

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Hill-Rom 305 Manual Bed, Руководство по обслуживанию, Страница: 10 / 176

Результаты поиска

Содержание 305 Manual Bed

Отзывы: