Hill-Rom 305 Manual Bed страница 84 Скачать руководство пользователя

Страница: 84 / 176

4.14 Hilow Crank Rod and Drive Screw Assembly Including Gas Springs (Manual Model Only)
Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 32

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

4.14 Hilow Crank Rod and Drive Screw Assembly Including Gas

Springs (Manual Model Only)

Tools required:

Small screwdriver

17 mm wrench

17 mm socket

Ratchet

10 mm hex wrench

13 mm socket

Removal

WARNING:

Do not work under an unsupported load. Install appropriate temporary
supports. Failure to do so could cause injury or equipment damage.

1. Put bed supports under the upper bed frame.

2. Raise the knee section and the head section to their highest positions.

3. Lift the foot section of the sleep surface, and fold it back toward the head

section.

NOTE:

If either of these sections cannot be raised, this procedure can be done from
underneath the foot end.

WARNING:

Attach the foot section to the head section. Failure to do so could cause
injury.

4. Use straps to attach the foot section to the head section.

5. Remove the footboard (A) from the bed frame (B) (see figure 4-14 on page

4-33).

6. Remove the plastic housing (C) from the crank handle assembly (D).

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды

Hill-Rom 305 Manual Bed, Руководство по обслуживанию

Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды