Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 74

Страница: 74 / 176

4.9 CPR Cable
Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 22

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

11. Lift the CPR wire (F) up and out of the lever (L).

12. Pull the CPR cable (C) out of the mount bracket (M).

Replacement

CAUTION:

Keep enough slack in the cables to allow the bed to move through its
full range of motion. Make sure the bed cables do not bind and do not
have any force applied to them. Failure to do so could cause equipment
damage.

1. When you route the cables, make sure they have enough slack for the bed

to move through its full range of motion.

2. Do the removal procedure in the reverse order.

Adjustment

Adjust the tension on the CPR cable (C) (refer to procedure 6.2 on page 6-11).

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Hill-Rom 305 Manual Bed, Руководство по обслуживанию, Страница: 74 / 176

Результаты поиска

Содержание 305 Manual Bed

Отзывы: