manualshive.com logo in svg

Hill-Rom 305 Manual Bed, Руководство по обслуживанию, Страница: 165 / 176

Поделиться
Скачать
Hill-Rom 305 Manual Bed Скачать руководство пользователя страница 165

6.2  CPR Cable Adjustment

Chapter 6: General Procedures

6

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Page 6 - 11 

 

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

6.2

CPR Cable Adjustment

Tools required:

Needle nose pliers

 

Small adjustable wrench

1. If the head section (A) does not lower quickly enough when you operate 

the CPR handle (B), do as follows (see figure 6-2 on page 6-12):

a. Loosen the screw (C) that attaches the CPR wire (D) to the bracket (E).

b. Pull a small part of the CPR wire (D) out of the cable (F).

c. While you hold the CPR wire (D) tightly, tighten the screw (C) to 

attach the wire (D) to the bracket (E).

NOTE:

While the CPR wire is held tightly, the head section will lower slowly.

d. Operate the CPR handle (B) to make sure the head section (A) lowers 

at the correct rate.

e. If the head section (A) does not lower quickly enough when the CPR 

handle (B) is operated, repeat step 1.

f. If the head section (A) lowers too quickly when the CPR handle (B) is 

operated, go to step 2.

Содержание 305 Manual Bed

















































































































































































Отзывы:

Нет отзывов