HBM GEN3i Скачать руководство пользователя страница 899 | Manualshive

Страница: 899 / 1160

HBM GEN3i Скачать руководство пользователя страница 899

E.13

The IRIG/GPS does not synchronize

l

Verify the settings. Is the correct synchronization source selected?

l

For IRIG, does the IRIG mode (such as “IRIG B AM”) match the IRIG
signal?

l

Check whether the connections are correct. For more information, please
refer to the corresponding chapter.

l

GPS synchronization can take a long time. Be patient. You may try
switching back to RTC and starting all over again.

l

Check whether the signal (IRIG) is free of distortions (e.g. record the IRIG
signal and check whether the amplitude

-

modulated sine wave is clean).

l

Check the positioning of the GPS antenna. The GPS synchronization
needs signals from at least three satellites for correct operation. Walls can
distort the signals from the satellites by blocking or reflecting them.

GEN3i

I3763-3.1 en HBM: public

899

«
...
897
898
899
900
901
...
»

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов