manualshive.com logo in svg

HBM GEN3i, Руководство пользователя, Страница: 183 / 1160

Поделиться
Скачать
HBM GEN3i Скачать руководство пользователя страница 183

11.4.1

I/O connector input overvoltage protection

All inputs of the I/O connector are over voltage protected. All inputs use the
following schematic approach.

To system timbase, trigger

and recording control

From input connector

+5V

20 kOhm

2 kOhm

+5V

Figure 11.14: 

I/O connector schematic inputs

Due to the 20 kΩ pull

-

up resistor all input will be “TTL High” and only need an

external short to signal ground to be operated. The 2 kΩ series resistor together
with the diode clamps to ground and +5 V protect the digital circuitry up to the
specified voltages.

The clamping diodes and other parasitic capacitors do create a capacitive load
on your signal source and limit the signal bandwidth. To reach the required
bandwidths detailed compensations are made not addressed in this block
diagram.

GEN3i

I3763-3.1 en   HBM: public

183

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов