HBM GEN3i Скачать руководство пользователя страница 345

Страница: 345 / 1160

Different amplifiers – Pros and Cons
Single

ended (to ground) amplifiers

Cost effective and small

High bandwidth

Easy to use with probes

Potential ground problems

No safety problems

No CMRR and no CMV

Single

ended isolated amplifier – unbalanced differential

Can perform differential measurements

Expensive and large

Difficult to use with probes

Limited CMRR, best CMV

Avoids ground loops

High level of safety

Differential amplifier (with common ground)

Widely used in DAQ

Good CMRR, limited CMV

No (safety) isolation and potential ground loops will remain present

Differential amplifier with isolated common

Safe

Expensive and large

Good CMRR, best CMV

More difficult to use with probes

GEN3i

I3763-3.1 en HBM: public

345

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GEN3i

Отзывы:

HBM GEN3i, Руководство пользователя, Страница: 345 / 1160

Результаты поиска

Содержание GEN3i

Отзывы: