HBM GEN3i Скачать руководство пользователя страница 213 | Manualshive

Страница: 213 / 1160

background image

12.2.3

GN610, Isolated 1kV 2MS/s input card

l

6 analog channels

l

Isolated, balanced differential inputs

l

±

20 mV to

±

1000 V input range

l

600 V RMS CAT II reinforced isolation, tested up to 6.4 kV

l

Analog/digital anti

-

alias filters

l

2 MS/s sample rate

l

18 bit resolution

l

2 GB memory

l

Two 4 mm banana plugs for each channel

l

Real

-

time cyclic calculators

l

Triggering on real

-

time results

l

Digital Event/Timer/Counter support

The isolated balanced differential inputs offers voltage ranges
from

±

20 mV to

±

1000 V.

The model uses two 4 mm safety banana plugs for each channel.
A standard safety rated BNC

-

to

-

banana adapter can be used to

easily connect coax cables using BNCs.
Tested up to 6.4 kV, the reinforced isolation allows for safe
measurements up to 600 V RMS CAT II (IEC61010

-

1:2010 safety

standard).
Optimum anti

-

alias protection is achieved by the 7

-

pole analog

anti

-

alias filter combined with a fixed 2 MS/s sampling Analog

-

to

-

Digital

converter. At lower sample rates the digital anti

-

alias filters allow for a large

range of high order filter characteristics with precise phase match and ultra low
noise output.
Besides the instantaneous values, the real

-

time cycle detection allows for cycle

based real

-

time calculations like TrueRMS on all analog channels as well as

torque, angle and speed on all timer counter channels simultaneously.
Every real

-

time calculated result can be used to trigger the recording.

If supported by the selected mainframe, the GEN DAQ series input card offers
16 digital input events, two digital output events and two Timer/Counter
channels.
The two Timer/Counters together with the GEN series mainframe Digital Event/
Timer Counter connector and the G070A torque/RPM adapter allow for direct
interfacing to HBM torque transducers or other torque and speed sensors.

For specification and ordering information, please refer to "B3618-4.2 en (GEN
series GN610)" on page 497.

1

2

!

2MΩ 1kVrms

CAT II 600V

3

!

2MΩ 1kVrms

CAT II 600V

4

!

2MΩ 1kVrms

CAT II 600V

5

!

2MΩ 1kVrms

CAT II 600V

6

!

2MΩ 1kVrms

CAT II 600V

!

2MΩ 1kVrms

CAT II 600V

GEN3i

I3763-3.1 en HBM: public

213

«
...
211
212
213
214
215
...
»

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GEN3i

Бренд: T&D Страницы: 2

Бренд: Beijing ART Tech Страницы: 19

Бренд: A&D Страницы: 28

Бренд: Ham Страницы: 4

Бренд: ACR Systems Страницы: 24

Бренд: ICP DAS USA Страницы: 131

Бренд: KYOWA Страницы: 47

Бренд: Metronic Страницы: 80

Бренд: Racelogic Страницы: 33

myDatalogNANO Ex

Бренд: Microtronics Страницы: 111

OM-EL-WiFi Series

Бренд: Omega Страницы: 2

Бренд: Solvera Lynx Страницы: 17

Бренд: Satel Страницы: 87

Бренд: Lumel Страницы: 39

Accu-Time 3610 Series

Бренд: ATS Страницы: 20

Бренд: Co2meter Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды