HBM AD104-R2 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 74

HBM AD104-R2 Скачать руководство пользователя страница 52

AD104-R2, AD104-R5

51 / 75

ba_aed104_8_e.doc

IDN

Identification

(Identification of transducer type and serial number)

Range:

Transducer type: 15 ASCII characters

Serial number:

7 ASCII characters

Factory setting:

depending on transducer

Response time:

Output:

<15ms

Input:

<180ms

Parameters:

1

Password protection:

none

Parameter protect.:

with input

Input:

IDN<"Transducertype">,<"Serial number">;

Entry of the transducer type and of the serial number.
The type and serial number of the transducer are filed in
the EEPROM of the transducer electronic unit. The type
designation may have maximum 15 characters and it
must be entered as string in quotation marks ("..."). If
only the serial number has to be changed, a comma is
entered for the transducer type parameter, e.g.

IDN,“0815

“;

The serial number is entered by the factory and may have maximum 7 characters, it is entered like the type
designation. The serial number must not be changed. If less than the maximum allowed number of characters is
entered for the type designation or serial number, the entry is automatically filled up with blanks up to the
maximum allowed number. The manufacturer and the software version cannot be entered.

Query:

IDN?;

Effect:

An identification string is output (33 characters).
Sequence: Manufacturer, transducer type, serial number, software version, e.g.
HBM, "AED104","1234", P20crlf
The number of the output characters is fixed. The transducer type is always

output with 15 characters, the serial number always with 7 characters.

«
...
50
51
52
53
54
...
»

Содержание AD104-R2











































































Отзывы:

Нет отзывов