HBM AD104-R2 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 74

HBM AD104-R2 Скачать руководство пользователя страница 23

22 / 75

ba_aed104_8_e.doc

Bus mode: COF16 to COF 28

If the decimal number 16 is added to the above stated output formats COF0...COF12, then the AED is switched
into the bus output mode. A measured value is output. The AED switches over to the partially active mode (each
new measured value is stored in the output buffer but not output). The measured value is output on the bus with
the select command S..;.

Example:

2 AED’s in bus operation

Command

Effect

S98;

All AED are partially active (listening but not transmission)

COF18;

Output in 2 byte binary output

ICR0;

Maximum measuring rate

MSV?0;

Continuous measurement in AED

S01;

Read measured value from 1st AED, immediate

output

of current measured value

, without

measuring time

S02;

Read measured value from 2nd AED, when response from first AED has been received
completely. Immediate

output

of current measured value

, without measuring time

S01;

Read measured value from 1st AED, when response from second AED has been received
completely

S02;

Read measured value from 1st AED, when response from second AED has been received
completely

...

...

STP;

Stop measured value output

S01;

Poss. new setting for 1st AED

Binary measured value output without CRLF: COF32 to COF44

If the decimal number 32 is added to the above stated binary output formats

COF0...COF12

, the AED is

switched into the following output mode for the measured values.
In the

binary measured value output

, the end character CR LF is left out, so that only 2 or 4 characters per

measured value are output. This measure increases the output speed of the measured values.

Format

Length Sequence of the measured value output

COF32

4 Byte

MSB before LSB

LSB=0 (no status)

COF34

2 Byte

MSB before LSB

COF36

4 Byte

LSB before MSB

LSB=0 (no status)

COF38

2 Byte

LSB before MSB

COF40

4 Byte

MSB before LSB

LSB=status/CRC

COF44

4 Byte

LSB before MSB

LSB=status/CRC

2-wire bus mode: COF64 ... COF76 (do not use for variants AD104-R2 and AD104-R5)

If the decimal number 64 is added to the above stated output formats

COF0...COF12

, then the AED is switched

into the 2-wire bus mode. This means that the AED answers no longer with “0“ or “?“ on command inputs. The
answer with the parameter or in the case of

MSV?

with the measured value occurs only for command enquiries

(e.g.

ASF?

). The command

MSV?0;

(continuous measured value transmission) may no longer be used in this

case since otherwise it is no longer possible to stop this output (apart from supply voltage off).

«
...
21
22
23
24
25
...
»

Содержание AD104-R2











































































Отзывы:

Нет отзывов