Gree GMV5 Series Скачать руководство пользователя страница 299

Страница: 299 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

295

Removal procedure of plate type heat exchanger

Note: Before removing the plate type heat exchanger, make sure no refrigerant is inside the pipeline and

power has been disconnected.

Step

Diagram

Operation Procedure

5. Install a new

plate type heat

exchanger

●Screw the support of plate

type heat exchanger and fix the

heat exchanger and the support

onto the chassis.

●Put on the plate type heat

exchanger based on the

position of the suction and

discharge pipes and weld the

pipes with the heat exchanger.

●During

welding,

charge

nitrogen into the pipes. The

pressure should be controlled

within 0.5±0.1kgf/cm

(relative

pressure). Note: Avoid nearby

parts from being burnt during

welding.

6. Fix and wire the

electric box.

●Put the electric b

ox back to

the original position and screw

it;

●Connect wires same as the

original.

7. Check and

install the front

panels.

●Check various parts and

connection wires;

●If no problem is found, hook

the front panels and tighten the

screws.

Содержание GMV5 Series


































































































































































































































































































































Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды

Gree GMV5 Series, Руководство по обслуживанию

Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды