Gree GMV5 Series Скачать руководство пользователя страница 295

Страница: 295 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

291

Removal procesure of oil separator

Note: Before removing the oil separator, make sure no refrigerant is inside the pipeline and power has

been disconnected.

Step

Diagram

Operation Procedure

4. Remove the

oil separator.

●Remove the oil separator

from chassis.

5. Install a new

oil separator.

●Weld the 4 joints on oil

separator;

During welding, charge

nitrogen into the pipes. The

pressure should be controlled

within

0.5±0.1kgf/cm

(relative pressure). Note:

Avoid nearby parts from being

burnt during welding;

●Screw the oil separator;

●Fasten the electric heating

belt.

6. Fix and wire

the electric box.

●Put the electric box back to

the original position and

screw it;

●Connect wires same as the

original.

7. Check and

install the front

panels.

●Check various parts and

connection wires;

●If no problem is found, hook

the front panels and tighten

the screws.

Содержание GMV5 Series


































































































































































































































































































































Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды

Gree GMV5 Series, Руководство по обслуживанию

Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды