Gree GMV5 Series Скачать руководство пользователя страница 185

Страница: 185 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

181

Troubleshooting:

2.3.4.33 “C8” Compressor emergency operation status.

Error display:

ODU mainboard will display

Error judgment condition and method:

If any compressor in the module is set with emergency operation status, the mainboard will display

“C8” to indicate that the system has entered compressor emergency operation status during operation

Possible reason

：

——

Troubleshooting:

status code, no troubleshooting.

2.3.4.34 “C9” Emergency operation status of fan.

ror display:

ODU mainboard will display

Error judgment condition and method:

If any fan in the module is set with emergency operation status, the mainboard will display “C8” to

indicate that the system has entered compressor emergency operation status during operation

Possible reason

：

——

Troubleshooting:

status code, no troubleshooting.

2.3.4.35 “CA” Emergency operation status of module.

Error display:

ODU mainboard will display

Error judgment condition and method:

If any compressor in the module is set with emergency operation status, the mainboard will display

“C8” to indicate that the system has entered compressor emergency operation status during operation

Содержание GMV5 Series


































































































































































































































































































































Результаты поиска

Содержание GMV5 Series

Отзывы:

Похожие инструкции для GMV5 Series

Бренды по названию

Популярные бренды

Gree GMV5 Series, Руководство по обслуживанию

Результаты поиска

Содержание GMV5 Series

Отзывы:

Похожие инструкции для GMV5 Series

Бренды по названию

Популярные бренды