Gree GMV5 Series Скачать руководство пользователя страница 126

Страница: 126 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

122

Cooling mode when the outdoor environment temperature is higher than 20°C(68

℉

Heating mode when the outdoor environment temperature is lower than 20°C(68

℉

(3) Before starting commissioning, make sure again that stop valves of all basic modules of the

ODU have been completely opened.

(4) During commissioning, the front panel of ODU must be completely covered. Otherwise,

commissioning accuracy may be affected (as shown in the following figure).

(5) Before commissioning, make sure that appending refrigerants to pipes has finished completely

or for more than 70%.

(6) The following table describes progress display of each phase during commissioning:

Progress Description for Commissioning Phases

——

Commissioning Code Progress Code

Status Code

Meaning

Progress

LED1

LED2

LED3

Code

Display

Status

Code Display

Status

Code

Display

Status

01_Master unit

setting detection

The system is in

non-commissioning status.

The system does not set any

master unit, and a master unit

should be set.

The system sets more than two

master units, and a master unit

should be set again.

The system successfully sets a

master unit and automatically

enters the next step.

02_Unit address

assignment

Blinking The system is assigning

addresses.

Blinking

There is not any master IDU, and a

master IDU should be set through

the commissioning software. If no

master IDU is set within one minute,

the system will automatically set

one.

The system successfully assigns

addresses and automatically

enters the next step.

03_Basic module

quantity

confirmation for

ODU

01-04

Blinking

LED3 displays the module quantity,

which should be manually

confirmed.

The system confirms the module

quantity and automatically enters

the next step.

04_Indoor unit

quantity

confirmation

01-80

Blinking

LED3 displays the IDU quantity,

which should be manually

confirmed.

The system confirms the IDU

quantity and automatically enters

the next step.

Содержание GMV5 Series


































































































































































































































































































































Результаты поиска

Содержание GMV5 Series

Отзывы:

Похожие инструкции для GMV5 Series

Бренды по названию

Популярные бренды

Gree GMV5 Series, Руководство по обслуживанию

Результаты поиска

Содержание GMV5 Series

Отзывы:

Похожие инструкции для GMV5 Series

Бренды по названию

Популярные бренды