Gree GMV5 Series Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 321

Gree GMV5 Series Скачать руководство пользователя страница 110

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

106

Step 1: Confirm entering the A2 refrigerant recovery operation settings. The master unit is displayed

as follows:

LED1

LED2

LED3

Function Code

Display Mode

Refrigerant

Recovery Code

Display Mode

Current Status

Display Mode

A2

On

01

Blinking

00

Blinking

Step 2: The default setting is “01”. Select "01" or "02" by pressing "SW1 (UP)" or "SW2 (DOWN)".

Press "SW7" to confirm selecting the mode.

On the master unit, press "SW6" to return to the upper level.
If no button operations are performed on the master unit for five minutes, the function setting

automatically quits and the unit restores the current status.



Indoor unit pipeline refrigerant recovery

Step 3: Select "01” as in step 2 to enter IDU refrigerant recovery. Digital LEDs and status LEDs of all

basic modules are displayed as follows:

LED1

LED2

LED3

Function

Code

Display

Mode

Refrigerant Recovery

Code

Display

Mode

Current Status

Display

Mode

A2

On

01

On

[Module low-pressure Ps]

On

LED3 shows the low-pressure value of a module. If the value is negative, LED3 circularly displays

the negative code "nE” and the numeric value every one second. For example, for -30

°

C, LED3

alternately displays “nE” for one second and then “30” for another second.

Step 4: Close liquid-tube stop valves of all basic modules of the ODU. When the low-pressure value

displayed on LED3 continually blinks, quickly close air-tube stop valves of all basic modules and then
press "SW7" on the master unit to confirm completing refrigerant recovery or power off the entire unit.

If no operations are performed after the low-pressure value displayed on LED3 continually blinks for

three minutes, the entire unit will be forcibly stopped.

On the master unit, press "SW6" to return to the upper level for restoring the standby status of the

entire unit (press "SW6" in setting status to return to the upper level; press "SW6" after settings are
completed to restore the normal operating status of the unit).

NOTICE!

Another startup is not allowed within 10 minutes after refrigerant recovery.



Basic module refrigerant recovery

Step 3: Set the basic module requiring refrigerant recovery to module emergency operation status

and close the liquid-tube stop valve of the emergency status module. Select "02” as in step 2 to enter
basic module refrigerant recovery. The display is as follows:

LED1

LED2

LED3

Function Code

Display Mode

Current Progress

Display Mode

Current Status

Display Mode

A2

On

02

On

Module high-pressure

On

LED3 shows the high-pressure value of the module.
Step 4: When the high-pressure value displayed on LED3 continually blinks (displayed as 0

°

C if the

high pressure is less than 0

°

C), quickly close the air-tube stop valve of the emergency module and then

press "SW7" on the master unit to confirm completing refrigerant recovery or power off the entire unit.

«
...
108
109
110
111
112
...
»

Содержание GMV5 Series


































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды