Gree GMV5 Series Скачать руководство пользователя страница 163

Страница: 163 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

159

Fault

code

Fault

Possible reasons

Solution

Primary reason

Secondary reason

Tertiary reason

Description

Confirmation

method

Description

Confirmation method

Description

Confirmation

method

High

pressure

protection

4. The pressure

sensor is faulty. ——

4.2 The high

pressure and

low pressure

sensors are

connected

reversely.

Connect the stop valve of

the module fluid pipe and

air pipe to the high and

low pressure gauges and

transform the readings

into corresponding

temperatures. Compare

them to the high- and

low-temperatures tested

by the system. If the

difference is larger than

5°C, it is exceptional.

——

Reconnect the high-

and low-pressure

sensors.

5. The high

pressure switch

is faulty.

E1 protection is

displayed on the

unit when it is

powered on.

5.1 The high

pressure switch

is not connected

to the main

board.

——

5.1.1 The pressure

switch is not

connected to the

main board.

——

Reconnect it.

——

5.1.2 The connect

wire between the

pressure switch and

main board is faulty.

——

Reconnect them

with the wire.

5.2 The high

pressure switch

is damaged.

——

Replace the

pressure switch.

6. The fan is not

working

properly.

A. The ODU's fan

does not work in

the cooling mode.

B. The IDU's

motor does not

work in the

heating mode.

6.1 The IDU's

fan is faulty.

Manual check

6.1.1 The power

cable connecting the

motor and main

board is loose.

Manual

check

Reconnect the

motor with the

power cable.

6.1.2 The electric

capacity is not

connected or is

damaged.

Manual

check

Connect or replace

the electric capacity.

6.1.3 The motor is

damaged.

Other

reasons

Replace the motor.

6.2 The ODU's

fan is faulty.

Manual check

6.2.1 The fan motor

is not properly

connected with the

control board of the

motor with the

power cable.

Manual

check

Reconnect it

properly.

6.2.2 The fan motor

is not properly

connected with the

control board of the

motor with the signal

feedback cable.

Manual

check

Reconnect it

properly.

6.2.3 The control

board of the fan's

motor is damaged.

Manual

check

Replace the control

board of the motor.

6.2.4 The main

board of the fan's

motor is damaged.

Other

reasons

Replace the motor.

7. Too much

refrigerant

Other reasons

Incorrect

quantity of

refrigerant is

injected.

——

Check the

necessary amount

of refrigerant and

discharge

unneeded

refrigerant slowly via

the stop valve of the

fluid pipe.

Содержание GMV5 Series


































































































































































































































































































































Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды

Gree GMV5 Series, Руководство по обслуживанию

Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды