Gree GMV5 Series Скачать руководство пользователя страница 257

Страница: 257 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

253

2.3.4.131 “U0” Insufficient compressor preheating time

Error display:

ODU mainboard, IDU wired controller and IDU receive light board will

display

Error judgment condition and method:

If it is detected that the oil temperature preheating time of compressor before startup doesn’t reach 8

hours, it will report this error.

Possible reason

：

——

Troubleshooting:

The complete unit shall be preheated for more than 8 hours before startup.

2.3.4.132 “U2” ODU capacity DIP switch/jumper cap setting error

Error display:

ODU mainboard, IDU wired controller and IDU receive light board will

display

Error judgment condition and method:

ODU mainboard detects that the capacity code doesn’t comply with the actual unit capacity, or ODU

mainboard detects that the jumper cap value doesn’t comply with the actual unit

ossible reason

：

■Capacity DIP switch is wrong or jumper cap is wrong (for those models without jumper cap, it won’t

be detected)

■DIP switch or jumper cap is broken

■Detecting circuit is abnormal

Troubleshooting:

2.3.4.133 “U3” Power phase sequence protection

Error display:

ODU mainboard, IDU wired controller and IDU receive light board will

display

Error judgment condition and method:

If phase loss or reverse of three-phase power is detected (e.g. incorrect connection of power supply

Содержание GMV5 Series


































































































































































































































































































































Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды

Gree GMV5 Series, Руководство по обслуживанию

Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды