manualshive.com logo in svg

Gree GMV5 Series, Руководство по обслуживанию

Поделиться
Скачать
Gree GMV5 Series Скачать руководство пользователя страница 188

GREE                                               Photovoltaic Direct-driven Inverter Multi VRF Units 

184 

2.3.4.40 “CJ” System address code conflict 

Error  display: 

ODU mainboard, IDU wired controller and IDU receive light board will 

display

 

Error judgment condition and method:

 

When multiple refrigerant system is connected through CAN2 network of unit mainboard, it is 

allowable to have only one master system in this network. 

When the system address DIP switch (SA2) of master controlling unit in two or more systems are 

detected as the master system DIP switch simultaneously, that is SA2 DIP switch is “00000”, it will report 
multiple master systems error. 

Possible reason

：

 

■When the system address DIP switch (SA2) of master controlling unit in two or more systems are 

set as the master system DIP switch, the SA2 DIP switch of master controlling unit in only one system 
shall keep as “00000”. The SA2 DIP switch of master controlling unit in other systems shall be set in 
different codes. 

■DIP switch is abnormal or mainboard is abnormal.

 

Troubleshooting:

 

 

2.3.4.41 “CP” Multiple master wired controller error 

Error  display: 

ODU mainboard, IDU wired controller and IDU receive light board will 

display

 

Error judgment condition and method:

 

There are two or more wired controllers in one HBS network are set as the master wired controller. 

Possible reason

：

 

When two (or more) wired controllers control one or several IDUs simultaneously, the two (or more) 

wired controller are master wired controller. 

Содержание GMV5 Series


































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды