Gree GMV5 Series Скачать руководство пользователя страница 158

Страница: 158 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

154

Fault

code

Fault

Possible reasons

Solution

Compressor drive IPM

over-temperature

protection

1. The compressor drive board is

faulty;

2. Thermal gel is not applied evenly

on the IPM module;

3. The IPM module is not screwed

properly.

1. Replace the compressor drive board;

2. Apply thermal gel evenly on the IPM

module;

3. Screw the IPM module properly.

Inverter compressor

out-of-step protection

The compressor drive board is faulty.

The compressor is damaged.

Replace the compressor drive board.

Replace the compressor.

Compressor drive DC

bus high voltage

protection

1. Does the voltage of the input power

cable of the whole system exceed 460

2. The compressor drive board is

faulty.

1. Lower the voltage of the input power

cable to the required range;

2. Replace the compressor drive board.

Compressor drive DC

bus low voltage

protection

1. Is the voltage of the input power

cable of the whole system lower than

320 V;

2. The compressor drive board is

faulty.

1. Elevate the voltage of the input power

cable to the required range;

2. Replace the compressor drive board.

Compressor drive

current check circuit

fault

1. The compressor drive board is

faulty.

1. Replace the compressor drive board.

Compressor drive

recharging circuit fault

1. Is the voltage of the input power

cable of the whole system lower than

280 V;

2. The compressor drive board is

faulty.

1. Elevate the voltage of the input power

cable to the required range;

2. Replace the compressor drive board.

Inverter compressor

starting failure

1. The drive board is damaged;

2. The compressor's UVW cable is

not connected properly;

3. The compressor is damaged.

1. Replace the compressor drive board;

2. Reconnect the compressor's UVW

cable;

3. Replace the compressor.

Communication failure

between main control

board and variable

frequency fan drive

1. The control board is powered off;

2. The fan drive board is powered off;

3. The communication cable between

the control board and fan drive board

is not connected;

4. The fan drive board's dial switch is

wrong.

1. Check the power supply of the control

board. Replace the control board if it

works properly;

2. Check the power supply of the drive

board. Replace the drive board if it works

properly;

3. Connect the main board and drive

board using the communication cable;

4. Adjust the dial switch of the fan drive

board.

Fan drive module reset

protection

1. The fan drive board is faulty.

1. Replace the fan drive board.

Variable frequency fan

over-current protection

1. The fan drive board's IPM module

is damaged;

2. The fan's UVW cable is not

connected properly;

3. The fan is damaged.

1. Replace the fan drive board;

2. Reconnect the fan's UVW cable;

3. Replace the fan.

Fan drive IPM module

protection

1. The fan drive board's IPM module

is damaged;

2. The fan's UVW cable is not

connected properly;

3. The fan is damaged.

1. Replace the fan drive board;

2. Reconnect the fan's UVW cable;

3. Replace the fan.

Fan drive temperature

sensor fault

1. The fan drive board is faulty.

1. Replace the fan drive board.

Fan drive IPM

over-temperature

protection

1. The fan drive board is faulty;

2. Thermal gel is not applied evenly

on the IPM module;

3. The IPM module is not screwed

properly.

1. Replace the fan drive board;

2. Apply thermal gel evenly on the IPM

module;

3. Screw the IPM module properly.

Variable frequency fan

out-of-step protection

The fan drive board is faulty.

The fan is damaged.

Replace the fan drive board.

Replace the fan.

Содержание GMV5 Series


































































































































































































































































































































Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды

Gree GMV5 Series, Руководство по обслуживанию

Результаты поиска

Содержание GMV5 Series

Отзывы:

Бренды по названию

Популярные бренды