manualshive.com logo in svg

Gree GMV5 Series, Руководство по обслуживанию, Страница: 220 / 321

Поделиться
Скачать
Gree GMV5 Series Скачать руководство пользователя страница 220

GREE                                               Photovoltaic Direct-driven Inverter Multi VRF Units 

216 

2.3.4.76 “H1” Fan drive board operation error 

Error display: 

IDU wired controller will display

 

 

Error judgment condition and method:

 

Check the error code on IDU wired controller. If IDU wired controller displays H1, you should also 

check the error code on nixie tube of ODU main control board. Judge the detailed error of fan drive board 
according to the error code on main control board and arrange troubleshooting accordingly. 

Possible reason

：

 

■Fan drive IPM module protection (Nixie tube on ODU main control board displays H6)

 

■Inverter fan overcurrent protection (Nixie tube on ODU main control b

oard displays H5) 

■Fan drive communication error (Nixie tube on ODU main control board displays C3)

 

Troubleshooting:

 

Step one: Check IDU wired controller error code 
Step two: Also check the error code on nixie tube of ODU main control board 
Step three: Arrange troubleshooting according to the error code displayed on ODU nixie tube 

(Detailed troubleshooting steps refer to the corresponding error) 

2.3.4.77 “H2” Fan drive board power supply voltage protection 

Error display: 

IDU wired controller will display

 

 

Error judgment condition and method:

 

Check the error code on IDU wired controller. If IDU wired controller displays H2, you should also 

check the error code on nixie tube of ODU main control board. Judge the detailed error of fan drive board 
according to the error code on main control board and arrange troubleshooting accordingly. 

Possible reason

：

 

■Fan drive DC bus high voltage protection (Nixie tube on ODU main control board displays HH)

 

■Fan drive DC bus low voltage protection (Nixie tube on ODU main cont

rol board displays HL) 

Troubleshooting:

 

Step one: Check IDU wired controller error code 
Step two: Also check the error code on nixie tube of ODU main control board 
Step three: Arrange troubleshooting according to the error code displayed on ODU nixie tube 

(Detailed troubleshooting steps refer to the corresponding error) 

2.3.4.78 “H3” Fan drive module reset protection 

Error display: 

IDU wired controller will display

 

Error judgment condition and method:

 

Check the error code on nixie tube of ODU main control board. If H3 is displayed, it indicates fan 

drive board module reset protection 

Possible reason

：

 

Содержание GMV5 Series


































































































































































































































































































































Отзывы:

Нет отзывов