Global Contract Licence 2, Руководство по установке

Страница: 11 / 100

•Page globalcontract.com 10
GLOBAL
Contract
• Fall 2017
INSTALLATION GUIDELINES
Included Hardware
L2DR-BL Single Pedestal Desk
Safety Glasses Rubber Mallet
Required Tools
NOTE: Open and assemble only one product
at a time to avoid a potential mix-up of parts
and hardware.
It is adviseable to assemble the unit on a
carpet to avoid scratches.
Screwdriver #2 Phillips
Assembly
“T” Nut Insert
L007250039
STEP 1:Unpack and inspect individual pieces for damages or missing hardware.
STEP 2: Pick a clean unobstructed area to assemble desk. It is advisable to as-
sembly of this product upright.
STEP 3: Handles for Pedestals are Shipped Installed on the inside of the cabinet.
Remove handle from the inside of the cabinet and re-install with the same screws
on the front of cabinet.
a. Levellers for pedestals are shipped inside the unit. These levellers should
be installed prior assembling complete unit.
L2DRHxxxxBL L2DBHxxxxBR L2DBxxxxBL
Modular Screw
L007250001
STEP 4: IArrange Pedestal and gable as per the fi nal confi guration of the product.
a. Using a 1/8” drill bit, drill though holes into side of pedestal according to
the provided template on the side of the pedestal exposed to the underside
of the desk. For this application, use the full modesty and recessed panel
location.
b. Modular screws are to be installed into these holes
STEP 5: Gable has Blum connectors pre-installed. Orient gable with Blum Connec-
tors facing inside of desk.
Install levelers into T nut inserts on the bottom of the Gable.
a. Install Blum Connector screws into pre-drilled holes on top edge of the gable
STEP 6: The modesty panel comes with Modular connectors installed on to con-
nect to the Pedestal.
On the top edge of the modesty panel, install Blum Connector screws into the pre-
drilled holes.
On side of Modesty panel lining up with the gable, install Blum Connector screws
into pre-drilled holes.
• There are 2 holes here, select hole closest to underside of assembly to
correctly line up with the Blum Connectors.
a. Attach the modesty panel to the pedestals by lining up modular con
nectors to screws installed on the pedestal, lift modesty and slide into
position ensuring to engage connectors to screws. You can use a mallet to
securely seat the modesty panel into position.
b. Connect the gable to the modesty panel by lining up Blum Connector
screws to the Blum connectors. Turn the screw on Blum Connector ¼ turn,
do not over tighten.
STEP 7: To install the worksurface top. The worksurface comes with Blum Connec-
tors pre-installed on the bottom of the surface. Lift worksurface over the assembly
and line up Blum connectors to the installed Blum connector screws on the mod-
esty panel and gable. Turn screw on Blum Connector ¼ turn, do not over tighten.
a. You must also secure the worksurface top to the pedestal. Line up the
top fl ush to the side and front of the pedestal. Use #8 x 3/4 wood screws
provided, screw through the mounting bar on the pedestal to secure the
top. Note: Drawers need to be removed to access drilling location.
STEP 8: When fi nal position has been located, level the unit with the levellers
installed on Gable and pedestal
Level
Installation For Similar Products
Leveler
L007250037 Blum Connector
Screw L005650060
92.2mm
96mm
102.7mm
9.5mm
162mm
FULL HEIGHT
MODESTY
HALF HEIGHT
MODESTY
FLUSH MOD 6” REC MOD
Back Panel
Top Underside
Wood Screw #8 3/4
L007250032
Blum Connector
(installed) L005650061 Modular Connector
(installed) L004250001