GILES FSH-4 Hood Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 68

background image

6

Model: FSH-4 Hood

Installation

IMPORTANT NOTE!!

If there is evidence of damage to the palletized unit, or any of the accompanying items, immediately and

thoroughly inspect the unit and all components. Notify the freight company of all damages. Generally, it is the

responsibility of the Customer to file and negotiate freight damage claims with freight carriers.

2.02

Unpacking

Unit is shipped on a wooden pallet, secured by high-tensile plastic strapping and wrapped in machine-applied

stretch wrap. In most cases a wooden framework is built around the unit for added protection. Unpack unit as

follows:
1. Position pallet in an area that provides adequate space for unpacking.
2. Remove the plastic stretch wrap, strapping and other packaging materials as necessary.
3. Carefully remove the hood stand components (sides, back panels, trim pieces & appliance channels) from the

shipping skid using suitable equipment and/or sufficient manpower and safe work practices. Stage all

components for installation or assembly.

4. Generally, the two (2) stainless baffle filters are packed on top of the hood. If so, secure them and place for

safekeeping.

5. Carefully remove any wooden supports and/or framework that might be attached.
6. Locate and secure the envelope containing Warranty Card and any other documentation or hardware provided

for installation.

7. It is preferable to leave the hood unit on the pallet so that handling equipment can be used to move it to the

desired permanent location after the stand is assembled and in place.

•

Unit is very heavy and bulky! Use suitable equipment and/or sufficient manpower to lift and move the Hood

from the shipping skid. See

Section 1.04.4, Weights

.

•

Take care when removing and disposing of packaging materials.

•

When moving and handling the hood, take special care not damage the bottom skirting. Dragging unit along

the floor or lifting using the bottom edge has the potential to damage the skirt portion.

•

Failure to comply with these

CAUTION

notices may result in moderate to minor injury, equipment or property

damage, and could void the warranty.

NOTE:

Items needed for stand and hood assembly (fasteners & tube of high temperature silicone) are provided with

the hood. All other expenses for material, labor, equipment rentals, etc. is the responsibilty of the purchaser,

not included with hood purchase.

Assemble stand with provided hardware and fasteners as shown as shown by the following instruction. Use the

provided tube of high-temp silicone, applying as shown.

2.03

Stand & Hood Assembly

Continued on Next Page

«
...
14
15
16
17
18
...
»

Содержание FSH-4 Hood





































































Отзывы:

Нет отзывов

Похожие инструкции для FSH-4 Hood

Бренд: JAC Страницы: 103

Бренд: 3Disc Страницы: 12

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Park House Healthcare Страницы: 12

Бренд: Cannon Страницы: 70

Бренд: Sakai Страницы: 31

Бренд: GE Страницы: 289

Бренд: York Fitness Страницы: 18

Бренд: 4B Страницы: 16

Бренд: FitEngine Страницы: 68

Maestro SB-CO-DIV-008B

Бренд: Pentair Страницы: 52

Бренд: PFM Medical Страницы: 26

Бренд: Master Страницы: 80

Бренд: Southwire Страницы: 15

Бренд: RAK Страницы: 50

Бренд: Sentinel Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды