GILES FSH-4 Hood Скачать руководство пользователя страница 55

Страница: 55 / 68

Model: FSH-4 Hood

Troubleshooting

6.01 Procedures - continued

Problem

Probable Cause

Corrective Action

Under-hood appliances will not

power-up:

•

[HOOD POWERED]

light

•

[CHARCOAL OR BAFFLE

FILTER

MISSING]

light

•

[

APPLIANCE POWERED]

light

OFF

a. A baffle filter is missing or not

properly installed

Install filter / check positioning.

b. A charcoal or pre-filter is missing

or not properly installed

Install filter / check positioning.

c. Faulty filter switches.

Test & replace as needed.

Under-hood appliances will not

power-up:

•

[HOOD POWERED]

light

•

[CHARCOAL OR BAFFLE

FILTER

CLOGGED]

light

•

[

APPLIANCE POWERED]

light

OFF

•

Continuous (steady) tone

alarm

sounding.

a. Baffle, pre-filter or charcoal filter

clogged

Replace charcoal or pre-filter • Clean

baffle filter.

b. Hood exhaust outlet excessively

block

Clear of any obstructions.

c. Vacuum switch is out of

adjustment

Test & adjust vacuum switch.

d. Kinked or blocked vacuum line Remove vacuum line kinks or

blockage.

e. Fans running slow or blades are

loaded with grease build-up.

Check voltage and inspect blowers

clean if needed

Under-hood appliances will not

power-up:

•

[HOOD POWERED]

light

•

[

WASH]

light

•

[

APPLIANCE POWERED]

light

OFF

•

Intermittent (beeping) tone

alarm

sounding.

a. Excessive grease film built up on

collector fins; too dirty

Clean the EAC cell,

Section 4.04.2

b. EAC cell is not installed

Install clean EAC cell.

c. EAC driver board is faulty

Test & replace EAC power supply if

needed.

d. Poor connection at contact

plate; dirty contacts, mis-

alignment, faulty contacts.

Check cell position, clean contacts,

inspect contact plate & replace if

needed.

e. Ionizer wire(s) missing

Replace missing wire(s)

Under-hood appliances operating:

•

[HOOD POWERED]

light

•

[CHECK

]

light

•

[

APPLIANCE POWERED]

light

•

alarm sounding, but cell is

NOT

cleaning air

a. Ionizer wire broken & touching

chassis.

Replace ionizer wire.

b. Collector fins shorted to ground

by moisture.

Dry cell, determine cause of

moisture, cool air being drawn into

hood creating condensation.

Under-hood lighting does not come

ON.

a. Bulb burned out

Replace bulb.

b. Faulty light switch

Check

replace switch.

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды