GILES FSH-4 Hood Скачать руководство пользователя страница 54

Страница: 54 / 68

Model: FSH-4 Hood

Troubleshooting

This section describes basic troubleshooting procedures for

FSH Recirculating Hoods

. Generally, troubleshooting

and/or repairs should only be performed by trained and qualified service technicians. Troubleshooting by Users

should be limited to issues that are operational or procedural in nature.

•

roubleshooting for electrical problems should be performed

ONLY

by trained service technicians or electricians.

Serious injury, even death, will result from contact with energized electrical circuits.

6.01 Procedures

Problem

Probable Cause

Corrective Action

Hood will not turn ON

a. A filter access door is open

Close & latch both doors.

b. Improper start-up method

Press & momenterily hold

[START]

portion (top) of power switch.

c. Power switch is faulty

Replace switch.

c. Improper supply voltage

Connect to proper electrical supply.

e. Not properly connected to

power source.

Confirm connections & correct.

f. Blown fuse or tripped circuit

breaker.

Check main electrical panel.

[CHARCOAL OR BAFFLE FILTER

MISSING] light ON at start-up

a. Baffle or charcoal filters not

installed or not properly seated

Install filter and/or check filter

positioning inside hood.

EAC [WASH] light ON & intermittent

(beeping) alarm sounding

a. Excessive film build-up on fins

Clean the EAC cell,

Section 4.04.2

b. EAC cell is not installed

Install EAC cell

c. Poor connection at contact plate

inside hood.

Check cell position, clean contacts.

d. Faulty EAC contact plate

Have plate inspected, replace if

needed.

e. Missing ionizer wires

Replace wires, (9) required.

EAC [CHECK] light ON; no alarm

sounding

a. EAC shorted to ground (damaged) Replace or repair the EAC cell.

b. High voltage wires shorted to

ground.

Correct shorted condition.

c. Collector fins shorted out due to

excessive moisture.

Eliminiate condensation causes - cold

air being drawn into hood, etc.

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды