GILES FSH-4 Hood Скачать руководство пользователя страница 11

Страница: 11 / 68

Model: FSH-4 Hood

Introduction

Control Panel:

• LED indicator lights display the performance status for each of the two (2) Electronic Air Cleaner collector cells.

• Indicator lights show status the hood’s operating status, providing signals that attention is required for conditions

which may be affecting performance ... missing filters, mis-aligned filters, clogged filters, airflow obstructions, etc.

•

APPLIANCE POWERED

light indicates whether or not under-hood appliances are being supplied powered.

Filters:

• (2) Baffle Filters - capture and remove large grease particulate.

• (2) Pre-Filters - capture and remove smaller grease particulate and moisture.

• (2) Electronic Air Cleaner (E.A.C.) Cells - electrostatically capture fine particle air contaminates.

• (2) Charcoal Filters - help to control undesirable cooking aromas in the exhaust air.

Push-To-Start Power:

Hood/appliance combination will not automatically restart when power is restored after an interruption. Power

switch must be pressed to start the hood and power appliances. Complies with code requirements in some

jurisdictions.

Pre-plumbed for Fire Suppression System:

Factory pre-plumbed and ready for connection to a listed fire suppression system

(Ansul R-102 wet chemical)

Includes piping, plenum nozzles

(not appliance drop-downs)

, detector link brackets and conduit.

The fire

extinguishing system, field installation/set-up, testing and final charging shall be provided by the purchaser,

and must be supplied by an authorized Ansul Distributor/Dealer ... not included with hood purchase

Hood is constructed primarily of Series 430 stainless steel; 16, 18 & 20 Ga.

Introduction

THANK YOU

for purchasing the

Giles Model FSH-4 Ventless Recirculating Hood w/72” Floor Stand

, manufactured

Giles Enterprises, Inc.

, Montgomery, Alabama (USA), hereafter referred to as

"GILES"

. Giles Ventless Hood

technology is the result of extensive engineering, research and development. Every unit is thoroughly inspected

and tested prior to shipment to ensure it operates flawlessly after installation. With proper care and maintenance

these units should provide years of trouble-free service.
To help protect your investment, we recommend that you take the time to review this Manual and become familiar

with the procedures in it pertaining to installation, operation, cleaning and maintenance. Adherence to

recommended procedures will minimize potential for costly “downtime” and future repair expense.

Please retain this Manual for future reference.

1.01

Construction

1.02

Design Features

1.03

Optional Features

HEPA Filter Model

A hood model equipped with (2) replaceable

HEPA

filters as an alternative to the standard Electronic Air Cleaner

system.

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды