GILES FSH-4 Hood Скачать руководство пользователя страница 22

Страница: 22 / 68

Model: FSH-4 Hood

Installation

1. Install appropriate circuit breaker in main electrical panel, see

Section 2.05, Electrical Specifications

2. As required by code, route suitable sized flexible conduit from main panel to service box on hood top and

attach using appropriate connectors. See

Section 2.05.2, Routing Conduit & Wiring

3. Pull appropriately sized wire from the electrical panel to the hood service box. Connect power supply wires

with wirenut and tape the connections with electrical tape.

4. Re-install Service Box Cover.
5. Turn

breaker supplying power to the Hood.

6. Press and hold in the top

[START]

portion of the

Power Switch

for a few seconds, then release when the

hood fan starts running. Switch springs back and remains in the

[ON]

position. The green

[POWER]

Light

turns

and an alarm breifly sounds until the fan reaches full speed. The amber

[APPLIANCE POWERED]

turns

7. Place Power Switch in the

[OFF]

position and continue installation.

2.05

Electrical Specifications - Hood ONLY

• Food service equipment must be properly grounded in accordance with local code, or in the absence of local

code, with the

National Electrical Code, ANSI/NFPA 70

Improper grounding may result in electrical shock to

Users. Check local electrical code to ensure that proper grounding techniques are used.

•

Always consult a certified electrician, or other qualified service technician, prior to installation to ensure that

electrical circuits are of sufficient rating for the Hood and Appliance load.

• Improper installation, adjustment, alteration, service or maintenance could result in serious injury or possible

death, equipment or property damage, and could void the warranty.

Electrical Specifications (Hood Only)

Unit

Voltage

Phase

Amps

Breaker

FSH-4

208-240

IMPORTANT!

•

Hood is designed to operate with either 208V or 240V supply power.

•

Breaker size shown applies to

hood power only

. Under-hood appliances are to be powered by a separate circuit

with an interlock relay controlled through the hood circuitry, so that appliances are not powered unless hood is

running properly.

2.05.1 Electrical Connections

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды