GILES FSH-4 Hood Скачать руководство пользователя страница 41

Страница: 41 / 68

Model: FSH-4 Hood

Operation & Filter Maintenance

4.02.7

E.A.C. Filter Cell Installation

E.A.C. Alignment Pin

Hood Contact

Plate (inside top)

Filter Contact

Plate

(UP)

Airflow arrow, on Cell front.

[Left]

[Right]

Folding Handle,

use avoid

damaging the

cell

IMPORTANT!

E.A.C. filter cells are side-specific. Give attention when placing

into hood to avoid improper positioning. Contact pads of both

cells must be position toward top of hood and airflow direction

arrow of each must point toward the center.
If cell does not engage the alignment pin and slide fully into the

hood, it is

NOT

positioned properly.

Brass contacts on cells

must make good contact

with the contacts inside

the hood.

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды