GILES FSH-4 Hood Скачать руководство пользователя страница 50

Страница: 50 / 68

Model: FSH-4 Hood

Hood Cleaning & Maintenance

This Section describes the steps to generally maintain and clean the

FSH-4 Hood

. Attention to these procedures will

help ensure the Hood remains in satisfactory operating condition and continues to run efficiently and safely.
A

Maintenance & Service Log

is provided, see

Section 5.04

The Hood design incorporates various interlock switches to ensure that the unit will shutdown if certain conditions exist

that are not consistent with safe and effective operation. The interlocks should be tested

MONTHLY

as described

below. Use the

Maintenance & Service Log

to record completion of testing. If problems are detected, contact

GILES

or an authorized service provider.

NOTE: Anytime a filter access door is opened and closed, the hood must be

restarted as described in Section 4.01

Door Interlock Test:

Start hood. With hood running, unlatch and slightly open each access doors, one at a

time. With each side confirm that hood powers

OFF

when opened and appliances under the hood cannot be

turned

Baffle Filter Test:

Remove the baffle filter from one side, then start hood. Verify that the red

[BAFFLE OR

CHARCOAL FILTER MISSING]

light turns

and the

[APPLIANCE POWERED]

light turns

OFF

. Check to

ensure that appliances under Hood will not turn

. Replace filter and repeat test with the other side’s

filter. See

Sections 4.02.2 & 4.02.3, Removal & Installation

Pre-Filter/Charcoal Filter Test:

Same procedure as

except perform for each pre-filter and charcoal filter,

one at a time in succession

. Reinstall the filters. See

Sections 4.02.4, 4.02.5, 4.02.8 & 4.02.9, Removal &

Installation

E.A.C. Filter Test:

Remove one of the E.A.C. collector cells, close and latch door, then start hood. Verify that

[WASH]

light on

E.A.C. Status

comes

for the side without cell and that the amber

[APPLIANCE

POWERED]

light is also

. Wait approx. two (2) minutes. A beeping tone alarm should begin sounding. In

several seconds the

[APPLIANCE POWERED]

light should turn

OFF.

Check to ensure that appliances under

hood cannot be turned

. Turn off hood, reinstall cell, and repeat for other side. See

Section 4.02.6. &

4.02.7, Removal & Installation

Filter Clogged Test:

Perform this test ONLY after installing new charcoal filters

Start hood normally and

allow to run. Use cardboard, or other suitable material, to completely block the hood exhaust outlet,

holding it firmly in place so that no air is escaping

Within a few seconds, a continuous tone alarm should

begin sounding. The red

[BAFFLE OR CHARCOAL FILTER CLOGGED]

light should turn

and the

[APPLIANCE

POWERED]

light should turn

OFF.

Check to ensure that appliances under hood cannot be turned

Remove the obstruction; the alarm should silence and the

[APPLIANCE POWERED]

light should turn

again.

Should any of these tests fail to yield the described results, contact a factory-authorized service company and have

the unit evaluated and repaired. A

Giles Manufacturer’s Representative

can provide information about nearby

authorized service providers, or call

GILES Services

at 800-554-4537

for assistance.

5.01

Monthly Hood Interlock Inspection (Can be Performed by User)

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды