GILES FSH-4 Hood Скачать руководство пользователя страница 15

Страница: 15 / 68

Installation

2.01

Location

Model: FSH-4 Hood

1. A minimum clearance of

14” (355.6 mm)

must be maintained between the top of the hood exhaust outlet and

the ceiling, or other overhead obstruction.

DO NOT

attach additional ductwork to the exhaust outlet in an attempt to redirect airflow. Resulting back

pressure can significantly reduce hood capture and result in unsatisfactory performance.

DO NOT

attempt to by-pass the ceiling clearance requirement by directing exhaust air into a ceiling niche, or

space above a suspended ceiling.

This section summarizes procedures necessary for proper equipment installation. To help avoid personal injury or

equipment damage, be sure to adhere to all of these recommended procedures.

Installation expense (materials & labor) is completely the Purchaser’s responsibility. Generally, it is advisable to

engage the services of a professional commercial kitchen equipment specialist, a licensed electrician, and/or a

qualified HVAC contractor to assist with the details of installation. Call

Giles Technical Suppor

t @ 800.554.4537, if

assistance is required.

The hood is factory assembled with piping, conduit, nozzles, detector link brackets, and exhaust fire damper. Upon

installation It must be connected to a,

customer provided,

fire suppression system specified by the UL listing, which

is the

Ansul® R-102 Wet Chemical system

The system. field installation/set-up, testing and final commissioning

shall be provided by the purchaser, and must be supplied an authorized

Ansul Distributor/Dealer

IMPORTANT!!

Before installing the GILES Recirculating/Ventless Hood system ensure that, A). all necessary approvals from local

code authorities have been obtained, B). the appliances to be used with the hood are all within the hood’s listing

limitations, as outlined in

Section 2.04

, and C). the installation site complies with the specific requirements and

limitations outlined in the

GFSE Recirculating/Ventless Hood Approval Letter (HAL)

. The

HAL

is available for

review or download at www.gfse.com under the

SUPPORT

tab in

VENTLESS DOCUMENTS

To ensure satisfactory hood performance after installation, the intended site MUST comply with minimum

requirements for kitchen size (>600 sq ft), ceiling height, fresh outdoor air make-up, supplemental exhaust

ventilation, clearances, etc. as stipulated in Giles’ Hood Approval Letter.

•

MAXIMUM of 1 hood per 600 sq ft of commercial kitchen space.

•

Fresh outside air make-up must be equal to a MINIMUM of fifteen (15) complete room air exchanges per hour.

•

Giles makes no representations as to proper design or layout of an establishment in which the ventless hood

will be used. Further, Giles does not perform site inspections prior to installation of any of its units.

• When operating, the hood produces a sound level of approximately

75 dB

•

DO NOT ALTER, ADD ATTACHMENTS OR OTHERWISE MODIFY THIS EQUIPMENT.

•

Failure to comply with installation requirements as specified by the Giles Hood Approval Letter will void the

factory warranty.

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды