GILES FSH-4 Hood Скачать руководство пользователя страница 8

Страница: 8 / 68

Safety

Specific Safety Precautions:

Model: FSH-4 Hood

For your safety, please observe the following precautions when operating or servicing this

GILES

food service

equipment. Adhering to the following important safety information will help to prevent personal injury and/or

damage to the equipment.

• Before cleaning or performing maintenance, place power switch in the

[OFF]

position. To remove all power

from the appliance, unplug power cord or turn

OFF

power at the electrical panel supplying the unit.

• Failure to place

Power Switch

in the

[OFF]

position when replacing filters, could result in equipment damage,

electrical shock and/or serious personal injury.

•

DO NOT

wash down interior or exterior of hood with water from a spray hose.

• Failure to comply with

DANGER

notices will result in serious injury, even death; or damage to equipment and/or

property and may void the factory warranty.

•

Ventless/recirculating hoods are

not

suitable for every commercial food service application. Failure to fully

comply with all site requirements and installation limitations as outlined in the

GFSE Hood Approval Letter

and this Manual

, may result in poor or highly unsatisfactory hood performance.

•

DO NOT

use ventless/recirculating hoods with gas-fired cooking appliance due to high potential of inhalation

hazard due to carbon monoxide build-up in the kitchen area. Hood is approved ONLY for use with electrically

heated appliances.

• Prior to installation, consult a qualified electrician to ensure that installation will comply with all electrical

requirements and codes.

• The unit must be adequately and properly grounded. Improper grounding may result in electrical shock to the

user. Always refer to local electrical code to ensure proper grounding of this or any other electrical equipment.

• Check the rating label on the unit to determine the proper power supply required. Always consult with an

electrician, or other qualified service technician, to ensure that circuit breakers and wiring are of sufficient rating

and gauge to power this equipment. A wiring diagram has been provided with the unit as an aid for technicians.

The unit must be installed and electrically grounded in accordance with local codes, or in the absence of local

codes, in accordance with the National Electrical Code, NFPA 70.

• Improper installation, alterations of the unit, or improper service/maintenance could result in serious injury,

even death; equipment and/or property damage; and will potentially void the factory warranty.

•

DO NOT

use or store flammable liquids, or materials that produce flammable vapors, in the vicinity of this or

any other appliance!

• Failure to comply with

WARNING

notices could result in serious injury, even death; damage to equipment

and/or property; and will potentially void the factory warranty.

Содержание FSH-4 Hood





































































Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды

GILES FSH-4 Hood, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание FSH-4 Hood

Отзывы:

Похожие инструкции для FSH-4 Hood

Бренды по названию

Популярные бренды